SS400 Steel

410 stainless steel specification

410 stainless steel specification

410 stainless steel specification

400 Series Stainless Steel Overview, Properties, and

The 400 series group of stainless steels typically have an 11% chromium and 1% manganese increase, above the 300 series group. This stainless steel series tends to be susceptible to rust and corrosion under some conditions although heat-treating will harden them. 410 - Rolled Alloys, Inc.410 stainless is a corrosion and heat resistant 12% chromium steel. It is the most widely used of the hardenable stainless steels. Heat treated 410 has mechanical properties comparable to the engineering alloy steel AISI 4130, coupled with the additional benefit of good corrosion resistance. 410 is highly resistant to atmospheric corrosion.

410 STAINLESS STEEL - Cleveland Metal Exchange

May 30, 2014 · Type 410 Stainless Steel is produced in coils and cut lengths in thicknesses 0.01 0.125 in. (0.25 3.18 mm) and widths up to 36 in. (914 mm). Values shown in this bulletin were established in U.S. customary units. The metric equivalents may be approximate. 410 Stainless Steel Properties KVA Stainless410 - UNS S41000:AISI Type 410 is a martensitic stainless steel that provides high strength and hardness with moderate corrosion resistance. A wide range of properties can be developed with different heat treatments, with ultimate tensile strengths ranging from 500 to 1400 MPa. 410 Stainless Steel SheetProductname 410 stainless steel sheet Specification Thickness:0.3mm-150mm Width:1000mm-2000mm Length:1000mm-6000mm Customized sizes are accepted

410 Stainless Steel, 410 SS, Grade 410 - Permanent Steel

Type 410 Stainless Steel sheet and strip is covered by the following specifications:AMS 5504, ASTM A240. Chemical Composition: 410 Stainless Steel, UNS S41000410 Alloy Description Alloy 410 is a martensitic stainless steel that provides moderate corrosion resistance plus high strength and hardness. This alloy can be hardened by cold working and by heat treating and is magnetic in both conditions. A wide of properties can 410 Stainless Steel, UNS S41000410 Stainless Steel, UNS S41000 Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated ASTM A240, ASTM A276, ASTM 479, ASTM 580, AMS 5504, AMS 5613 410 Alloy Description Alloy 410 is a martensitic stainless steel that provides moderate corrosion resistance plus high strength and hardness.

410CB Stainless Steel

410CB is an AOD + ESR melted martensitic stainless steel alloy. This alloy has elevated strength and toughness as compared to standard 410. The addition of columbium allows for improved grain size control and greater ease in heat treating. This grade is used primarily in the power generation market. AISI 316 Stainless Steel vs. AISI 410 Stainless Steel May 30, 2020 · Both AISI 316 stainless steel and AISI 410 stainless steel are iron alloys. They have 81% of their average alloy composition in common. There are 35 material properties with values for both materials. Properties with values for just one material (1, in this case) are not shown. AMS 5504 / Stainless Steel 410 - Aircraft MaterialsType 410 Stainless Steel is available in Sheet, Plate, Strip, Wire, Billet, Forging Stock, Bar (Round, Flats, Squares, Hex). View Stock List, Plate Stock List or contact Sales for further availability. Specifications Type 410 Stainless Steel is covered by the following specifications:AMS 5504 Sheet / strip / plate AMS 5505 Sheet / strip

ASTM A479 Grade 410 2 - Martensitic Stainless Steel -

A Martensitic Stainless Steel also known as DIN 1.4006 ,JIS SUS410 ,ISO X10Cr13with Mechanical, thermal and chemical properties.. Datasheet Download. See where ASTM A479 Grade 410 2 falls on the material property chart for Density against Elastic modulus in your materials selection and design process. Our Ashby charts are interactive Atlas Grade datasheet 410 rev May 2008 July 2010Grade 410is the basic martensitic stainless steel; like most non-stainless steels it can be hardened by a "quench-and-temper" heat treatment. It contains a minimum of 11.5 per cent chromium, just sufficient to give corrosion resistance properties. It achieves maximum corrosion resistance when it has been hardened and tempered and then polished. Stainless Steel - Grade 410 (UNS S41000)

  • Topics CoveredIntroductionKey PropertiesCompositionMechanical PropertiesPhysical PropertiesGrade Specification ComparisonPossible Alternative GradesCorrosion ResistanceHeat ResistanceHeat TreatmentWeldingMachiningApplicationsGrade 410 stainless steels are general-purpose martensitic stainless steels containing 11.5% chromium, which provide good corrosion resistance properties. However, the corrosion resistance of grade 410 steels can be further enhanced by a series of processes such as hardening, tempering and polishing. Quenching and tempering can harden grade 410 steels. They are generally used for applications involving mild corrosion, heat resistance and high strength.Martensitic stainless steels are fabricat410 Stainless Steel Cutlery - Sandmeyer SteelAlloy 410 is a 12% chromium martensitic stainless steel that, when heated, hardens to achieve optimum strength and edge retention. Because of these qualities, it is commonly used in the manufacturing of cutlery.

    Stainless Steel Specification and Composition Chart

    10 rows · 410 - Heat-treatable stainless used widely where corrosion is not severe - air, fresh water, Stainless Steel Specification and Composition Chart Stainless Steel Specification and Composition Table Chart. Metal Products Distributor Supplier Metals and Materials Table of Contents. 410 - Heat-treatable stainless used widely where corrosion is not severe - air, fresh water, some chemicals and food acids. 416 - Free machining variation of 410 with useful corrosion resistance to natural Stainless Steel Type 410 Rolled Metal Products Description Type 410 is a corrosion and heat resistant martensitic stainless steel containing approximately 12% chromium offering a wide range of mechanical properties through heat treatment. This grade offers a moderate level of corrosion resistance and the maximum resistance is obtained by hardening through heat treatment followed by polishing.

    410 Stainless Datasheet - United Performance Metals

    410 Stainless Datasheet. Type 410 is hardenable, straight-chromium stainless steels which combine superior wear resistance of high carbon alloys with the excellent corrosion resistance of chromium stainless steels. Oil quenching these alloys from temperatures between 1800°F to 1950°F (982-1066°C) produces the highest strength and/or wear resistance as well as corrosion resistance.

Contact us

Email: [email protected]